Feit SHOP/4/HO/CCT/AG Teardown

The SHOP/4/HO/CCT/AG shop light is a 10,000 lumen light with tunable white light (3000K – 6500K) with a NEMA 5-15P connector that plugs into a standard 3-prong outlet.

It can be found in the US on Amazon and in retailers such as Costco for about $60 (as of the time of publishing). It’s an interesting design (in my opinion) because it’s a smart light that supports on/off, dimming, and CCT color. But at the flip of a switch you can use it just like a standard, dumb LED light.


The light module contains 6 rows of LEDs (84 LEDs/row), each row alternating between cold and warm, for a total of 504 LEDs.

Major Integrated Circuits

In addition to your usual collection of resistors, capacitors, and diodes, there’s three inductors which I couldn’t figure out P/N information for. I think there’s also a thermistor or fuse of some kind (magenta circled item on top side of of PCB). I’ve highlighted the major ICs below and provided some information based on what I could find:

WB2L (BK7231T chip)

Manufacturer: Tuya

P/N: WB2L (BK7231T chip)

Function: Low-power embedded Wi-Fi and Bluetooth LE module. The chip is on a daughter board which is solder to the main board perpendicularly through a thru hole. There’s a switch that overrides the WB2L (and removes power from it!) and sets the light to cool white (not cold) color.

Pin No.SymbolI/O typeBK7231T FunctionUse
1PWM2I/OHardware PWM pin; P8/BT_ACTIVE/PWM2 (Pin24)Dimmer
2PWM1I/OHardware PWM pin; P7/WIFI_ACTIVE/PWM1 (Pin23)Color Temperature
3PWM0I/OHardware PWM pin; P6/CLK13M/PWM0 (Pin22)No Connect
4PWM5I/OHardware PWM pin; P26/IRDA/PWM5 (Pin15)Unknown
5PWM4I/OHardware PWM pin; P24/LPO_CLK/PWM4 (Pin16)No Connect
6GNDPGround pinGND
73V3PPower supply pin (3.3 V)3.3 V

For this light, here’s what my probing found:

  • PWM1: 0% duty cycle is full Cold and 100% duty cycle is full Warm
  • PWM2: 0% duty cycle is off and 100% duty cycle is full brightness.
  • PWM5: Unknown if this is an input or an output. With the stock Feit firmware:
    • Logic 0: when the light is on
    • Logic 1: when the light is off


Manufacturer: Bright Power Semiconductor

P/N: BP2525

Function: Non-isolated step-down type AC/DC Constant Voltage chip…power for the LEDs that is then current controlled by the BP2929 (for color temperature) and BP5012 (for dimming).


Manufacturer: Bright Power Semiconductor

P/N: BP5929

Function: Dual-channel PWM color matching chip1

This is an interesting chip, and I’m not quite sure why they’re using it. Normally, the microcontroller would output two PWM signals: one for Cool White and one for Warm White, and they would each drive a MOSFET and then dimming is handled algorithmically by the microcontroller. This chips seems to offload that functionality (sort of; this chip doesn’t actually handle dimming itself, but rather in combination with a separate current control method — which I believe is the BP5012 in this design), but I’m not sure why…the microcontroller can do all of this easily. My one thought is that maybe this method reduces flicker because it’s relies of constant voltage instead of using PWM to vary the voltage.

Pin NumberNameDescription
1VHHigh-voltage side power supply terminal
2VSHigh pressure side floating
3OUT2Output GATE signal 2
4OUT1Output GATE signal 1
5NCNot Connected
6PWMPWM Signal Input
7VCCLow voltage power supply
Google translation of datasheet…so may not be exactly accurate


Manufacturer: Bright Power Semiconductor

P/N: BP5012 or BP501 (maybe)

Function: PWM dimming interface converter (probably)

I couldn’t find a datasheet for BP5012 or BP501. There is a BP5011 though, which is a 2 channel PWM dimming controller. So I suspect it’s related to that.


Manufacturer: Joulwatt

P/N: JW1602

Function: Non-isolated switching regulator with dimming

The package is marked JW1606, but JW1606 doesn’t exist. I’m assuming this is related to the JW1602, which I was able to find a datasheet for.

The JW1602 has dimming function, so I’m not sure why the duplicate functionality with the BP5012. The BP2525 is also a non-isolated switching regulator as well. So my theory is that there’s two completely separate control circuits on the PCB, one to provide variable control of color temperature and intensity when the microcontroller is active and another circuit that provides fixed color temperature (probably just 50/50) and a fixed dimming level (set by a voltage divider).


Manufacturer: onSemi


Function: Bridge Rectifier. Probably for input to both of the non-isolated switching regulators (BP2525 and JW1606).


Manufacturer: CR Micro

P/N: CRJF380N65G2

Function: SJ-MOS N-MOSFET. I think this is used only when the unit is in “dumb” mode and provides the variable current control for all 504 LEDs.


Manufacturer: Silan Microelectronics


Function: N-CHANNEL MOSFET. There’s two of these that are directly connected to the LEDs themselves, one for each color temperature. These are probably driven by the BP5929 to control the current for each set of LEDs.


Manufacturer: CT Micro

P/N: CT2N7002E-R3

Function: N-Channel Enhancement MOSFET. I think this is somehow related to the mysterious function of PWM5.


BK7231T is pretty straight forward:

  1. Remove two screws from cord side (red circles)
  2. Remove cord clamp (green circle)
  3. Slide the the PCB out from its slot
    Note: this might require scrapping some of the potting compound used to the secure the PCB into the slot. Pushing gently from the end using the switch usually pops it out


I flashed the unit with OpenBK7231T/OpenBeken, which now supports this light. I followed the UART instructions, which requires using https://github.com/OpenBekenIOT/hid_download_py.

I used a USB to Serial USB to TTL CH340G to program the chip. Once the PCB is removed, make the following connections:

  • Connect computer TX to U1_RXD (Top side: red arrow)
  • Connect computer RX to U1_TXD (Top side: green arrow)
  • Connect a wire to the RST (Top side: magenta arrow), when you’re ready to program you’ll briefly connecting this to ground to reset the chip.
  • Connect 3.3 volts to 3V3 (Bottom side: red arrow)
  • Connect ground to GND (Bottom side: black arrow)

Outstanding Questions

  • What does PWM5 do?
  • Does power get cut to WB2L when switch is activated?
  • What are the other chips?
  • What chip is used for LED control?
  1. This is a Google Translation…so may not be exactly accurate